[  217.295466] PM: suspend entry (s2idle)

[  217.300132] Filesystems sync: 0.004 seconds

[  217.306786] Freezing user space processes

[  222.186199] qcom-apm-audio-pkt gprsvc:service:2:1: CMD timeout for [1001013] opcode

[  222.198475] Freezing user space processes completed (elapsed 4.891 seconds)

[  222.198491] OOM killer disabled.

[  222.198494] Freezing remaining freezable tasks

[  222.201335] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)

[  222.201341] printk: Suspending console(s) (use no_console_suspend to debug)

[  223.597971] qcom-pcie 1c10000.pcie: Device not found

[  223.914014] qcom-pcie 1c00000.pcie: PCIe Gen.3 x1 link up

[  223.924915] geni_i2c 890000.i2c: Unbalanced pm_runtime_enable!

[  223.928098] geni_i2c a90000.i2c: Unbalanced pm_runtime_enable!

[  223.928126] geni_i2c 894000.i2c: Unbalanced pm_runtime_enable!

[  224.035862] arm-smmu 15000000.iommu: Unhandled context fault: fsr=0x402, iova=0x5a7dccd40, fsynr=0x220011, cbfrsynra=0xa0, cb=10

[  224.035874] arm-smmu 15000000.iommu: FSR    = 00000402 [Format=2 TF], SID=0xa0

[  224.035879] arm-smmu 15000000.iommu: FSYNR0 = 00220011 [S1CBNDX=34 WNR PLVL=1]

[  224.050305] xhci-hcd xhci-hcd.0.auto: WARNING: Host Controller Error

[  225.141885] onboard-usb-dev 2-1: device not accepting address 2, error -108

[  225.741875] onboard-usb-dev 2-1: device not accepting address 2, error -108

[  226.342471] onboard-usb-dev 2-1: device not accepting address 2, error -108

[  226.942368] onboard-usb-dev 2-1: device not accepting address 2, error -108

[  227.111547] OOM killer enabled.

[  227.111552] Restarting tasks: Starting

[  227.112127] onboard-usb-dev 1-1: USB disconnect, device number 2

[  227.112408] onboard-usb-dev 2-1: USB disconnect, device number 2

[  227.112917] Restarting tasks: Done

[  227.112929] efivarfs: resyncing variable state

[  227.115150] usb usb2-port1: couldn't allocate usb_device

[  227.121154] usb usb1-port1: couldn't allocate usb_device

[  227.334510] efivarfs: finished resyncing variable state

[  227.335724] PM: suspend exit

[  227.345488] wlp1s0: deauthenticating from f0:61:c0:fb:1a:90 by local choice (Reason: 3=DEAUTH_LEAVING)

[  227.488230] qcom-ethqos 23040000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-0

[  227.488653] qcom-ethqos 23040000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-1

[  227.489239] qcom-ethqos 23040000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-2

[  227.489730] qcom-ethqos 23040000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-3

[  227.633005] qcom-ethqos 23040000.ethernet end0: PHY [stmmac-0:1c] driver [Qualcomm QCA8081] (irq=POLL)

[  227.645305] qcom-ethqos 23040000.ethernet end0: Enabling Safety Features

[  227.645489] qcom-ethqos 23040000.ethernet end0: IEEE 1588-2008 Advanced Timestamp supported

[  227.647391] qcom-ethqos 23040000.ethernet end0: registered PTP clock

[  227.647408] qcom-ethqos 23040000.ethernet end0: configuring for phy/2500base-x link mode

[  231.976403] wlp1s0: authenticate with f0:61:c0:fb:1a:90 (local address=04:68:74:b7:1a:db)

[  231.976420] wlp1s0: send auth to f0:61:c0:fb:1a:90 (try 1/3)

[  231.981177] wlp1s0: authenticated

[  231.983207] wlp1s0: associate with f0:61:c0:fb:1a:90 (try 1/3)

[  231.994521] wlp1s0: RX AssocResp from f0:61:c0:fb:1a:90 (capab=0x411 status=0 aid=17)

[  232.024617] wlp1s0: associated

[  250.843462] qcom-apm-audio-pkt gprsvc:service:2:1: CMD timeout for [1001013] opcode

[  273.370845] qcom-apm-audio-pkt gprsvc:service:2:1: CMD timeout for [1001013] opcode 